PHOTO SOON

Jones & Shipman 540
Surface grinder

18" x 6"  grinding capacity, fitted with a quality 14" x 6"
magnetic chuck, variable hydraulic powerfeed to table,
with variable auto crossfeed, 3 phase 440 volt spindle motor and hydraulic power pack, the machine runs
nicely and quietly
 

£950.00

SOLD

Perrin AV-3 Boring Machine

Made in Switzerland

Superb high quality boring machine,
previously used in the automotive industry
for cylinder boring, variable spindlespeed
power traverses in 2 directions, variable power
downfeed to the head, imperial dials, optical
scales, a very nice machine

£2750.00

DESCRIPTION SOON

Photo Soon

Harrison M300 Centre Lathe With Accessories

300mm swing with 600mm between centres. Metric dials, full screwcutting
gearbox with powerfeeds to the carriage and crosslide.  12 spindle speeds 40
to 2500 rpm, it has  a dual voltage 3 phase 220/250 380/440 volt main motor
and a coolant pump,  4 way indexing toolpost, 3 morse taper to the tailstock,
machine light, it is on the manufacturers stand. It has a 4 jaw self
centering chuck and a 200mm 4 jaw independent chuck both  
have the D1-3 camlock spindle fitting. There is a faceplate, lathe
tools and drills and other tooling.  It is a quiet runner and the screws and
slides are a very snug fit,  and the bed shows hardly any wear at all. 
I will include a machine manual with parts list. overall dimensions
58" long x 27" deep (plus guard) x 47" high 

(You can run this machine on an inverter from a 240volt single phase supply...Ask)

£2250.00

Heckert  Heavy Duty
Universal  Milling Machine
 

Universal mill, swivelling & tilting tee slot table, 30 international
spindle fitting, 16 spindle speeds 40 to 2000 rpm, 2 H.P.
3 phase motor, power feeds all round, swivelling vertical head,
high quality machine in very good condition,
with a coolant system,
 

£1650.00

TOS FNK 25 Heavy Duty
Turret Milling Machine
 

Heavy duty, vertical turret mill, 49" x 10" tee slot table, 30 international
spindle fitting, 16 spindle speeds 56 to 4500 rpm, 2.5 K.W.
3 phase motor 415 volt 2 speed motor, 12 speed power feed
gearbox to table with rapids3 speed , powerfeed to quill,
swivelling & tilting head, high quality machine
in very good condition, with a coolant system,
 

£1850.00

(You can run this machine on an inverter from a 240volt single phase supply...Ask)

Thiel Model 158 Universal Milling Machine

With vertical head (not seen in photo)

Universal mill with horizontal & vertical machining facility,
swivellin & tilting tee slot table, 40 international
spindle fitting, 18 spindle speeds 40 to 2000 rpm, 2 H.P.
3 phase motor, power feeds in all directions, swivelling vertical
head,  high quality machine in very good condition,
with a coolant system,
 

Arriving Soon P.O.A.

(You can run this machine on an inverter from a
240volt single phase supply...Ask)

Bridgeport Turret  Milling Machine
 

Turret mill, 42" x 9" tee slot table, swivelling
& tilting head, standard R8
spindle fitting, power feed to head,
spindle speeds 67 to 4600 rpm,
1.5 H.P. 3 phase motor, power feeds to
table,  with a coolant system,
 

£925.00

SOLD

Hardinge HLV-H Centre Lathe

High quality toolroom spec. lathe, 12 speeds to 2500 rpm,
10" swing x 24" between centres, 2 MT to tailstock, 5C collet system,
coolant supply

Arriving Soon P.O.A.

(You can run this machine on an inverter from a 240volt single phase supply...Ask)

Deckel KF12, 3 Dimensional
Die Sinker/Engraver

No details as yet still located on site

P.O.A.

Deckel KF1, 3 Dimensional
Die Sinker/Engraver

No details as yet still located on site

P.O.A.

Studer Jig Mill

No details as yet still located on site

P.O.A.

Myford Woodturning
Lathe With Accessories
 

Recently removed from a woodturning
enthusiasts workshop. Originally a Myford wood
lathe which has been extensively and skilfully
modified by its previous owner to increase the
centre height to enable bowl turning and it also has a metal turning attachment seen in the photos.  It has
a 23" swing over the bed" with 24" between centres. 
It has 8 spindle speeds from 60 to 2200 rpm, 4 speeds
by step pulleys all driven by a 2 speed high low control box, the 3 phase 415 volt motor which is about 1 or 1.5 h.p.  it would be very easy to change to 240 volt single
phase, should the buyer need to,  (or better still use an inverter) It has a 2 morse taper to the tailstock,  a 5"
quality 3 jaw chuck and a host of other usefull tooling
and attachments.This lathe runs very quietly and all the
work is done and it is ready to use. The overall dimensions are 43" long x 20" deep x 45" high and 
the weight is about 320 kg

£375.00

SOLD

Quality 8" Planing Machine

I cannot see the makers nameplate but it looks
like a quality machine to me, normally
bench mounted the previous owner has
mounted it on its own heavy duty stand. 
The table is  41" x 9" and it is adjstable
in height to alter the cutting depth and it is
fitted with an adjustable angle fence. 
The motor is a Brooks 3 phase, 415 volts
1410 rpm and is about 1.5 h.p
it could easily be changed to single phase
or you could run it on 240volts using an inverter

£275.00

SOLD

10" Industrial Sawbench

Again no makers nameplate but it looks like a Statrite to me but I may be wrong, the table is 
26" x 23" and fitted with an angle fence and
it has a  10"  diameter T.C.T. blade, the motor
is 3 phase, 415 volts 1430 rpm and is about 1.5 h.p.  (If you do not have 3 phase then the motor would be easy to change to single phase or you could run it on an inverter (available on Ebay
from the Drives direct shop)  The overall dimensions are 23" wide  x  29" deep  x  3
8" high and the weight is about 150 kg. 
a good quality machine

£295.00


SOLD

Hardinge HLV-H
Centre Lathe

High quality toolroom spec. lathe, 12 speeds
to 2500 rpm,10" swing x 24" between centres,
2 MT to tailstock, 5C collet system,
coolant supply

Arriving Soon P.O.A.

5 Available

Denford TDS 12"
Disc Sander

12" disc, well guarded, ex-school.
1.0 h.p. 3 phase motor
could easily be changed to
240 volt

£195.00

Bridgeport BRM Turret 
Milling Machine

early model non-powerfeed head

Turret mill, 42" x 9" tee slot table,
swivelling & tilting head, high speed
head 2 M.T.spindle fitting,
10 spindle speeds to 4000 rpm,
1.0 H.P. 3 phase motor, with a coolant system,
 

Arriving Soon P.O.A.

Photo Soon

Elliott Radial 36" Drill

Heavy duty radial arm drill, rise
and fall table, 3 morse taper,
power downfeeds,

£1650.00

Keetona  K5 Hand Shear

Heavy duty hand operated sheet metal,
or bar shear, bench mount it or make
suitable stand 5" cut width, 5 foot
makes light work of hand shearing jobs.
Very expensive new!

£80.00

Minni Rettifiche Heavy
Duty Swing Grinder

8" Diameter segmented vertical cup wheel,
10" x 5" Mag Chuck 4 H.P. 3 phase,
2840 rpm, 415 volt motor,  12" Throat,
67" High x 30" wide x 32" deep
coolant supply

£895.00

Photo Soon

Alexander Model 3A Engraving Machine
 

It has a 240 volt single phase motor,
1420 rpm 1/3 horse power, with imperial
dials. The pattern table is 450mm x 320mm
and the work piece table is 200mm x 345mm
and both of the tables have rise and fall knee facility with independent 'X' axis control with
fine feed control and the work table also
has 'Y' axis control. The cutter head also
has quick action retract facility.

£550.00

SOLD

Alexander Model 2 Engraving
Machine
 

Superb machine in very good condition

It has a 240 volt single phase motor, 1420 rpm
1/3 horse power, with imperial dials.  3 Axis movement
to the  work table, the pattern table is 550mm x 325mm
and the work table is 500mm x 200mm.  The cutter head
also has quick action retract facility.  The weight is
approximately 275 kg. and  I have included a spare belt
and also an instruction manual to the machine.

£395.00

SOLD

XYZ VL355 CNC Lathe

Retains manual operation as well as CNC

Dixon quick-change toolpost, fully enclosed , large memory,
can be manually operated, fully programmeable, coolant supply
ready for work, with all manuals. Control tuition before delivery.

You can view this machine running on site, try before you buy !!!
 

£6795.00

Yang 15A Slant Bed CNC Lathe

Active toolpost, high performance machine.

 
 Barfeed unit, swarf conveyor, Fanuc OT controller,slant bed, full compliment of tooling.
a superb machine, with all manuals. Control tuition before delivery.

You can view this machine running on site, try before you buy !!!

£8995.00

Specima
Cylindrical
Grinder

Very high quality German machine,
swivel wheelhead, swivel workhead,
swivel table, metric dials, hand operated




£695.00

(You can run this machine on an inverter
from a 240volt single phase supply...Ask)

Smart & Brown
1024 Centre Lathe

High quality toolroom spec. lathe
 12 speeds to 2500 rpm,
10" swing x 24" between centres,
2 MT to tailstock, 3 & 4 jaw chucks,
coolant supply

£895.00


(You can run this machine on an inverter
from a 240volt single phase supply...Ask)